Protocol Files

1. General Information

A protocol file describes the communication with one device type. It contains protocols for each function of the device type and variables which affect how the commands in a protocol work. It does not contain information about the individual device or the used communication bus.

Each device type should have its own protocol file. I suggest to choose a file name that contains the name of the device type. Don't use spaces in the file name and keep it short. The file will be referenced by its name in the INP or OUT link of the records which use it. The protocol file must be stored in one of the directories listed in the environment variable STREAM_PROTOCOL_PATH (see chapter Setup).

The protocol file is a plain text file. Everything not enclosed in quotes (single ' or double ") is not case sensitive. This includes the names of commands, protocols and variables. There may be any amount of whitespaces (space, tab, newline, ...) or comments between names, quoted strings and special characters, such as ={};. A comment is everything starting from an unquoted # until the end of the line.

Example Protocol File:

# This is an example protocol file

Terminator = CR LF;

# Frequency is a float
# use ai and ao records

getFrequency {
    out "FREQ?"; in "%f";
}

setFrequency {
    out "FREQ %f";
    @init { getFrequency; }
}

# Switch is an enum, either OFF or ON
# use bi and bo records

getSwitch {
    out "SW?"; in "SW %{OFF|ON}";
}

setSwitch {
    out "SW %{OFF|ON}";
    @init { getSwitch; }
}

# Connect a stringout record to this to get
# a generic command interface.
# After processing finishes, the record contains the reply.

debug {
    ExtraInput = Ignore;
    out "%s"; in "%39c"
}

2. Protocols

For each function of the device type, define one protocol. A protocol consists of a name followed by a body in braces {}. The name must be unique within the protocol file. It is used to reference the protocol in the INP or OUT link of the record, thus keep it short. It should describe the function of the protocol. It must not contain spaces or any of the characters ,;={}()$'"\#.

The protocol body contains a sequence of commands and optionally variable assignments separated by ;.

Referencing other protocols

To save some typing, a previously defined protocol can be called inside another protocol like a command without parameters. The protocol name is replaced by the commands in the referenced protocol. However, this does not include any variable assignments or exception handlers from the referenced protocol. See the @init handlers in the above example.

Limitations

The StreamDevice protocol is not a programming language. It has neither loops nor conditionals (in this version of StreamDevice). However, if an error occurs, e.g. a timeout or a mismatch in input parsing, an exception handler can be called to clean up.

3. Commands

Seven different commands can be used in a protocol: out, in, wait, event, exec, disconnect, and connect. Most protocols will consist only of a single out command to write some value, or an out command followed by an in command to read a value. But there can be any number of commands in a protocol.

out string;
Write output to the device. The argument string may contain format converters which are replaced by the formatted value of the record before sending.
in string;
Read and parse input from the device. The argument string may contain format converters which specify how to interpret data to be put into the record. Input must match the argument string. Any input from the device should be consumed with an in command. If a device, for example, acknowledges a setting, use an in command to check the acknowledge, even though it contains no user data.
wait milliseconds;
Just wait for some milliseconds. Depending on the resolution of the timer system, the actual delay can be slightly longer than specified.
event(eventcode) milliseconds;
Wait for event eventcode with some timeout. What an event actually means depends on the used bus. Some buses do not support events at all, some provide many different events. If the bus supports only one event, (eventcode) is dispensable.
exec string;
The argument string is passed to the IOC shell as a command to execute.
disconnect;
Disconnect from the hardware. This is probably not supported by all busses. Any in or out command will automatically reconnect. Only records reading in "I/O Intr" mode will not cause a reconnect.
connect milliseconds;
Explicitely connect to the hardware with milliseconds timeout. Since connection is handled automatically, this command is normally not needed. It may be useful after a disconnect.

4. Strings

In a StreamDevice protocol file, strings can be written as quoted literals (single quotes or double quotes), as a sequence of bytes values, or as a combination of both.

Examples for quoted literals are:
"That's a string."
'Say "Hello"'

There is no difference between double quoted and single quoted literals, it just makes it easier to use quotes of the other type in a string. To break long strings into multiple lines of the protocol file, close the quotes before the line break and reopen them in the next line. Don't use a line break inside quotes.

As arguments of out or in commands, string literals can contain format converters. A format converter starts with % and works similar to formats in the C functions printf() and scanf().

StreamDevice uses the backslash character \ to define some escape sequences in quoted string literals:
\", \', \%, and \\ mean literal ", ', %, and \.
\a means alarm bell (ASCII code 7).
\b means backspace (ASCII code 8).
\t means tab (ASCII code 9).
\n means new line (ASCII code 10).
\r means carriage return (ASCII code 13).
\e means escape (ASCII code 27).
\x followed by up to two hexadecimal digits means a byte with that hex value.
\0 followed by up to three octal digits means a byte with that octal value.
\1 to \9 followed by up to two more decimal digits means a byte with that decimal value.
\? in input matches any byte, in output it does not print anything.
\_ in input matches any amount of white space (including none), in output it prints a single space.
\$ followed by the name of a protocol varible is replaced by the contents of that variable.

For non-printable characters, it is often easier to write sequences of byte values instead of escaped quoted string literals. A byte is written as an unquoted decimal, hexadecimal, or octal number in the range of -128 to 255, -0x80 to 0xff (not case sesitive), or -0200 to 0377, respectively.

StreamDevice also recognizes the ASCII symbolic names (not case sensitive) for several byte codes:
NUL (= 0x00) null
SOH (= 0x01) start of heading
STX (= 0x02) start of text
ETX (= 0x03) end of text
EOT (= 0x04) end of transmission
ENQ (= 0x05) enquiry
ACK (= 0x06) acknowledge
BEL (= 0x07) bell
BS  (= 0x08) backspace
HT or TAB (= 0x09) horizontal tabulator
LF or NL (= 0x0A or 10) line feed / new line
VT  (= 0x0B or 11) vertical tabulator
FF or NP (= 0x0C or 12) form feed / new page
CR  (= 0x0D or 13) carriage return
SO  (= 0x0E or 14) shift out
SI  (= 0x0F or 15) shift in
DLE (= 0x10 or 16) data link escape
DC1 (= 0x11 or 17) device control 1
DC2 (= 0x12 or 18) device control 2
DC3 (= 0x13 or 19) device control 3
DC4 (= 0x14 or 20) device control 4
NAK (= 0x15 or 21) negative acknowledge
SYN (= 0x16 or 22) synchronous idle
ETB (= 0x17 or 23) end of transmission block
CAN (= 0x18 or 24) cancel
EM  (= 0x19 or 25) end of medium
SUB (= 0x1A or 26) substitute
ESC (= 0x1B or 27) escape
FS  (= 0x1C or 28) file separator
GS  (= 0x1D or 29) group separator
RS  (= 0x1E or 30) record separator
US  (= 0x1F or 31) unit separator
DEL (= 0x7F or 127) delete
SKIP or ? matches any input byte

A single string can be built from several quoted literals and byte values by writing them separated by whitespaces or comma.

Examples:

The following lines represent the same string:
"Hello world\r\n"
'Hello',0x20,"world",CR,LF
72 101 108 108 111 32 119 111 114 108 100 13 10

5. Protocol Variables

StreamDevice uses three types of variables in a protocol file. System variables influence the behavior of in and out commands. Protocol arguments work like function arguments and can be specified in the INP or OUT link of the record. User variables can be defined and used in the protocol as abbreviations for often used values.

System and user variables can be set in the global context of the protocol file or locally inside protocols. When set globally, a variable keeps its value until overwritten. When set locally, a variable is valid inside the protocol only. To set a variable use the syntax:
variable = value;

Set variables can be referenced outside of quoted strings by $variable or ${variable} and inside quoted strings by \$variable or \${variable}. The reference will be replaced by the value of the variable at this point.

System variables

This is a list of system variables, their default settings and what they influence.

LockTimeout = 5000;
Integer. Affects first out command in a protocol.
If other records currently use the device, how many milliseconds to wait for exclusive access to the device before giving up?
WriteTimeout = 100;
Integer. Affects out commands.
If we have access to the device but output cannot be written immediately, how many milliseconds to wait before giving up?
ReplyTimeout = 1000;
Integer. Affects in commands.
Different devices need different times to calculate a reply and start sending it. How many milliseconds to wait for the first byte of the input from the device? Since several other records may be waiting to access the device during this time, LockTimeout should be larger than ReplyTimeout.
ReadTimeout = 100;
Integer. Affects in commands.
The device may send input in pieces (e.g. bytes). When it stops sending, how many milliseconds to wait for more input bytes before giving up? If InTerminator = "", a read timeout is not an error but a valid input termination.
PollPeriod = $ReplyTimeout;
Integer. Affects first in command in I/O Intr mode (see chapter Record Processing).
In that mode, some buses require periodic polling to get asynchronous input if no other record executes an in command at the moment. How many milliseconds to wait after last poll or last received input before polling again? If not set the same value as for ReplyTimeout is used.
Terminator
String. Affects out and in commands.
Most devices send and expect terminators after each message, e.g. CR LF. The value of the Terminator variable is automatically appended to any output. It is also used to find the end of input. It is removed before the input is passed to the in command. If no Terminator or InTerminator is defined, the underlying driver may use its own terminator settings. For example, asynDriver defines its own terminator settings.
OutTerminator = $Terminator;
String. Affects out commands.
If a device has different terminators for input and output, use this for the output terminator.
InTerminator = $Terminator;
String. Affects in commands.
If a device has different terminators for input and output, use this for the input terminator. If no Terminator or InTerminator is defined, the underlying driver may use its own terminator settings. If InTerminator = "", a read timeout is not an error but a valid input termination.
MaxInput = 0;
Integer. Affects in commands.
Some devices don't send terminators but always send a fixed message size. How many bytes to read before terminating input even without input terminator or read timeout? The value 0 means "infinite".
Separator = "";
String. Affects out and in commands.
When formatting or parsing array values in a format converter (see formats and waveform record), what string to write or to expect between values? If the first character of the Separator is a space, it matches any number of any whitespace characters in an in command. To match arbitrary amount of whitespace in input, use "\_".
ExtraInput = Error;
Error or Ignore. Affects in commands.
Normally, when input parsing has completed, any bytes left in the input are treated as parse error. If extra input bytes should be ignored, set ExtraInput = Ignore;

Protocol arguments

Sometimes, protocols differ only very little. In that case it can be convenient to write only one protocol and use protocol arguments for the difference. For example a motor controller for the 3 axes X, Y, Z requires three protocols to set a position.

moveX { out "X GOTO %d"; }
moveY { out "Y GOTO %d"; }
moveZ { out "Z GOTO %d"; }

It also needs three versions of any other protocol. That means basically writing everything three times. To make this easier, protocol arguments can be used:

move { out "\$1 GOTO %d"; }

Now, the protocol can be references in the OUT link of three different records as move(X), move(Y) and move(Z). Up to 9 parameters, referenced as $1 ... $9 can be specified in parentheses, separated by comma. The variable $0 is replaced by the name of the protocol.

User variables

User defined variables are just a means to save some typing. Once set, a user variable can be referenced later in the protocol.

f = "FREQ";     # sets f to "FREQ" (including the quotes)
f1 = $f " %f";  # sets f1 to "FREQ %f"

getFrequency {
    out $f "?"; # same as: out "FREQ?"; 
    in $f1;     # same as: in "FREQ %f"; 
}

setFrequency {
    out $f1;    # same as: out "FREQ %f"; 
}

6. Exception Handlers

When an error happens, an exception handler may be called. Exception handlers are a kind of sub-protocols in a protocol. They consist of the same set of commands and are intended to reset the device or to finish the protocol cleanly in case of communication problems. Like variables, exception handlers can be defined globally or locally. Globally defined handlers are used for all following protocols unless overwritten by a local handler. There is a fixed set of exception handler names starting with @.

@mismatch
Called when input does not match in an in command.
It means that the device has sent something else than what the protocol expected. If the handler starts with an in command, then this command reparses the old input from the unsuccessful in. Error messages from the unsuccessful in are suppressed. Nevertheless, the record will end up in INVALID/CALC state (see chapter Record Processing).
@writetimeout
Called when a write timeout occurred in an out command.
It means that output cannot be written to the device. Note that out commands in the handler are also likely to fail in this case.
@replytimeout
Called when a reply timeout occurred in an in command.
It means that the device does not send any data. Note that in commands in the handler are also likely to fail in this case.
@readtimeout
Called when a read timeout occurred in an in command.
It means that the device stopped sending data unexpectedly after sending at least one byte.
@init
Not really an exception but formally specified in the same syntax. This handler can be used to initialize an output record with a value read from the device. See also chapter Record Processing.

Example:

setPosition {
    out "POS %f";
    @init { out "POS?"; in "POS %f"; }
}    

After executing the exception handler, the protocol terminates. If any exception occurs within an exception handler, no other handler is called but the protocol terminates immediately. An exception handler uses all system variable settings from the protocol in which the exception occurred.